FrSky New RXSR F4 & F7 Flight Controllers Release
The FrSky RXSR-FC (OMNIBUS F4 V6) uses the MPU6000 over SPI for the stable flight performance. It is integrated with the RXSR receiver in onboard damping box, also onboard are a barometer and AB7456 OSD chip for the Betaflight integrated OSD.
The RXSR-FC (OMNIBUS F4 V6) supports 3-6s Lipo direct input, and has 5 hardware UARTs.
SPECIFICATIONS :
● STM32 F405 MCU, Runs Betaflight firmware (supported from v3.2)
● FrSky RXSR receiver in damping box
● MPU6000 over SPI Bus in damping box
● 30.5×30.5 mm mounting holes
● Supports Lipo direct plugin (3-6S)
● Supports 5V 1A BEC output (Buck)
● Supports 8V 1A BEC with LC filter output for the camera and VTX (Buck)
● STM32 controls OSD chip over SPI in DMA mode (Betaflight OSD)
FEATURES :
● RXSR Receiver
● STM32 F4 Processor
● MPU6000 Gyro via SPI
● BMP280 Barometer
● Integrated Betaflight OSD
● 5 UART Ports
● Direct plugin 3-6S Lipo
● Built in LC Filter
● 5V 1000mA BEC
● 8V 1000mA BEC
● More caps to reduce gyro power noise.
MORE DETAILS: https://www.frsky-rc.com/product/rxsr-fc-omnibus-f4-v6/
FrSky RXSR-FC (OMNIBUS F4 Fireworks V2)
The FrSky RXSR-FC (OMNIBUS F4 Fireworks) uses the ICM20608 over SPI for the best possible flight performance. It is integrated with the RXSR receiver in onboard damping box, and the ICM20608 runs perfectly under 32k Gyro loop. Also onboard are a barometer and AB7456 OSD chip for the Betaflight integrated OSD.
The RXSR-FC (OMNIBUS F4 Fireworks) supports 3-6s Lipo direct input, build in hall Current Sensor and Power Filter too. The on Board PDB is tweaked by using 12-Layer PCB design. There is only 0.2-0.5 mohm internal resistance from input to each output pads.
SPECIFICATIONS :
● STM32 F405 MCU, Runs Betaflight firmware (supported from v3.2)
● FrSky RXSR receiver in damping box
● ICM20608 over SPI Bus in damping box (optional MPU6000)
● 30.5×30.5 mm mounting holes
● Supports Lipo direct plugin (3-6S)
● Supports 5V 1A BEC output (Buck)
● Supports 8V 1A BEC with LC filter output for the camera and VTX (Buck)
● STM32 controls OSD chip over SPI in DMA mode (Betaflight OSD)
● Built-in hall Current Sensor
● Built-in Professional Level PDB
● More caps to reduce power noise.
FEATURES :
● Tantalum Capacitors can be added to the board (not included)
● Solder pads added for VTX and Camera Control (next to Video pads)
● The orientation of IMU FPC optimized
● Gyro ribbon cable redesigned to fit without extending outside the board
● Added an 8v BEC and LC Filter for the camera and VTX power
● This board now has 5 UART ports
MORE DETAILS: https://www.frsky-rc.com/product/rxsr-fc-omnibus-f4-fireworks-v2/
FrSky RXSR-FC (OMNINXT F7)
The FrSky RXSR-FC (OMNINXT F7) is developed based on the newly designed NXT architecture. It is integrated with RXSR receiver, and uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k loop time. The NXT also comes with 2 different BECs and 6 UARTs.
The RXSR-FC (OMNINXT F7) supports 3-6s Lipo direct input, built-in BEC for camera / VTX and Power Filter. This FC is designed to be able to pair with 4in1 ESCs to form a powerful combo, and also has pins for individual ESCs too.
SPECIFICATIONS :
● F7 MCU processors
● FrSky RXSR receiver in damping box
● Two gyros onboard: MPU6000 for sampling up to 8khz and ICM20608 for sampling up to 32khz
● 30.5×30.5 mm mounting holes
● Supports 3-6S Lipo
● More caps to reduce power noise
● Built-in 5V 1A BEC output (Buck)
● Built-in 8V 1A BEC with LC filter output for the camera and VTX (Buck)
● STM32 controls OSD chip over SPI in DMA mode (Betaflight OSD)
● Port for easy connection to 4-in-1 esc (SH1.0 8P)
● Solder pads added for VTX and Camera Control (next to Video pads)
FEATURES :
● RXSR Receiver
● STM32 F7 MCU Processor
● Gyro #1: MPU6000 8kHz
● Gyro #2: ICM20608 32kHz
● Integrated PDB & OSD (SPI/DMA)
● 6 UART Ports
● Direct plugin 3-6S Lipo
● 5V 1000mA BEC
● 8V 1000mA BEC with LC filter
● 3.3V max. 200mA
MORE DETAILS: https://www.frsky-rc.com/product/rxsr-fc-omninxt-f7/
